收藏本站
25AA040/25LC040/25C040
2.0
PIN DESCRIPTIONS
2.4
Serial Input (SI)
The descriptions of the pins are listed in Table 2-1.
The SI pin is used to transfer data into the device. It
receives instructions, addresses and data. Data is
TABLE 2-1:
PIN FUNCTION TABLE
latched on the rising edge of the serial clock.
Name
PDIP
SOIC
TSSOP
Description
2.5
Serial Clock (SCK)
CS
SO
WP
V SS
1
2
3
4
1
2
3
4
3
4
5
6
Chip Select Input
Serial Data Output
Write-Protect Pin
Ground
The SCK is used to synchronize the communication
between a master and the 25XX040. Instructions,
addresses or data present on the SI pin are latched on
the rising edge of the clock input, while data on the SO
pin is updated after the falling edge of the clock input.
SI
SCK
5
6
5
6
7
8
Serial Data Input
Serial Clock Input
2.6
Hold (HOLD)
HOLD
V CC
7
8
7
8
1
2
Hold Input
Supply Voltage
The HOLD pin is used to suspend transmission to the
25XX040 while in the middle of a serial sequence
without having to retransmit the entire sequence again
at a later time. It must be held high any time this func-
2.1
Chip Select (CS)
tion is not being used. Once the device is selected and
A low level on this pin selects the device. A high level
deselects the device and forces it into Standby mode.
However, a programming cycle which is already
initiated or in progress will be completed, regardless of
the CS input signal. If CS is brought high during a
program cycle, the device will go in Standby mode as
soon as the programming cycle is complete. When the
device is deselected, SO goes into the high-impedance
state, allowing multiple parts to share the same SPI
bus. A low-to-high transition on CS after a valid write
sequence initiates an internal write cycle. After power-
up, a low level on CS is required prior to any sequence
being initiated.
a serial sequence is underway, the HOLD pin may be
pulled low to pause further serial communication
without resetting the serial sequence. The HOLD pin
must be brought low while SCK is low, otherwise the
HOLD function will not be invoked until the next SCK
high-to-low transition. The 25XX040 must remain
selected during this sequence. The SI, SCK and SO
pins are in a high-impedance state during the time the
part is paused and transitions on these pins will be
ignored. To resume serial communication, HOLD must
be brought high while the SCK pin is low, otherwise
serial communication will not resume. Lowering the
HOLD line at any time will tri-state the SO line.
2.2
Serial Output (SO)
The SO pin is used to transfer data out of the 25XX040.
During a read cycle, data is shifted out on this pin after
the falling edge of the serial clock.
2.3
Write-Protect (WP)
Thi s pin is a hardware write-protect input pin. When
WP is low, all writes to the array or STATUS register
are disabled, but any other operation functions
normally. When WP is high, all functions, including
nonvolatile writes operate normally. WP going low at
any time will reset the write enable latch and inhibit
programming, except when an internal write has
already begun. If an internal write cycle has already
begun, WP going low will have no effect on the write.
See Table 3-3 for Write-Protect Functionality Matrix.
DS21204E-page 6
? 2006 Microchip Technology Inc.
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
25C080-I/P IC EEPROM 8KBIT 3MHZ 8DIP
25C320-E/P IC EEPROM 32KBIT 3MHZ 8DIP
25LC010AT-E/MC IC EEPROM 1KBIT 10MHZ 8DFN
25LC040AT-E/MC IC EEPROM 4KBIT 10MHZ 8DFN
25LC080A-I/STG IC EEPROM 8KBIT 10MHZ 8TSSOP
25LC1024T-E/MF IC EEPROM 1MBIT 20MHZ 8DFN
25LC128-E/MF IC EEPROM 128KBIT 10MHZ 8DFN
25LC160/P IC EEPROM 16KBIT 2MHZ 8DIP
相关代理商/技术参数
25C040X-E/P 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4K SPI ⑩ Bus Serial EEPROM
25C040X-E/SN 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4K SPI ⑩ Bus Serial EEPROM
25C040X-E/ST 功能描述:电可擦除可编程只读存储器 512x8 - 5V Rot Pin RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
25C040X-EST 制造商:未知厂家 制造商全称:未知厂家 功能描述:SPI Serial EEPROM
25C040X-I/P 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4K SPI ⑩ Bus Serial EEPROM
25C040X-I/SN 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4K SPI ⑩ Bus Serial EEPROM
25C040X-I/ST 功能描述:电可擦除可编程只读存储器 512x8 - 5V Rot Pin RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
25C040X-I/STG 功能描述:电可擦除可编程只读存储器 512x8 - 5V Rot Pin Lead Free Package RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8